DinizApp/Electronics Center
-
An inductor usually consists of a coil of conducting material, typically insulated copper wire, wrapped around a core either of plastic or of a ferromagnetic material; the latter is called an "iron core" inductor. When the current flowing through an inductor changes, the time-varying magnetic field induces an electromotive force. Small value inductors can also be built on integrated circuits using the same processes that are used to make transistors. Aluminum interconnect is typically used, laid out in a spiral coil pattern. However, the small dimensions limit the inductance, and it is far more common to use a circuit called a gyrator that uses a capacitor and active components to behave similarly to an inductor. Inductors used to block very high frequencies are sometimes made by stringing a ferrite bead on a wire.
An inductor usually consists of a coil of conducting material, typically insulated copper wire, wrapped around a core either of plastic or of a ferromagnetic material; the latter is called an "iron core" inductor. When the current flowing through an inductor changes, the time-varying magnetic field induces an electromotive force. Small value inductors can also be built on integrated circuits using the same processes that are used to make transistors. Aluminum interconnect is typically used, laid out in a spiral coil pattern. However, the small dimensions limit the inductance, and it is far more common to use a circuit called a gyrator that uses a capacitor and active components to behave similarly to an inductor.
Inductors used to block very high frequencies are sometimes made by stringing a ferrite bead on a wire.
Um indutor é geralmente construído como uma bobina de material condutor, por exemplo, fio de cobre. Um núcleo de material ferromagnético aumenta a indutância concentrando as linhas de força de campo magnético que fluem pelo interior das espiras. Indutores podem ser construídos em circuitos integrados utilizando o mesmo processo que é usado em chips de computador. Nesses casos, normalmente o alumínio é utilizado como material condutor. Porém, é raro a construção de indutores em CI's; eles são volumosos em uma pequena escala, e praticamente restritos, sendo muito mais comum o uso de um circuito chamado "gyrator", que utiliza um capacitor comportando-se como se fosse um indutor.
Pequenos indutores usados para frequências muito altas são algumas vezes feitos com um fio passando através de um cilindro de ferrite. -
Resistor Measurement
Resistor Measurement
Medição de Resistor -
FET Measurement (N-channel)
FET Measurement
(N-channel)Medição de Transistor
FET (canal N) -
Transistor in good condition
Transistor in good condition
Transistor em bom estado -
Burned transistor
Burned transistor
Transistor queimado -
Shorted transistor
Shorted transistor
Transistor em curto -
LED Measurement
LED Measurement
Medição de Led
-
Capacitor Measurement
Capacitor Measurement
Medição de Capacitor -
Diode Measurement
Diode Measurement
Medição de Diodo
-
Transformer Measurement
Transformer Measurement
Medição de Transformador -
Potentiometer Measurement
Potentiometer Measurement
Medição do potenciômetro
-
UJT Measurement
UJT Measurement
Medição de TJU -
UJT in good condition
UJT in good condition
TJU em bom estado -
Burned UJT
Burned UJT
TJU queimado -
UJT in short-circuit
UJT in short-circuit
TJU em curto -
Transistor Measurement
Transistor Measurement
Medição de Transistor -
TRIAC Measurement
TRIAC Measurement
Medição de Triac -
TRIAC in good condition
TRIAC in good condition
Triac em bom estado -
Burned TRIAC
Burned TRIAC
Triac queimado -
TRIAC in short-circuit
TRIAC in short-circuit
Triac em curto