Gibberfish, Inc./Gibberfish Management Portal
-
django.po.
Added 61 new segments
and no segments obsoleted.
New segments:
- Enter encryption passphrase
- Username
- Passphrase
- Enter code to confirm
- Old passphrase
- New passphrase
- Confirm new passphrase
- Enter SSH public key
- CAUTION:
- Adding SSH keys will allow 'root' logins on your server.
- The root user will have complete and total access to your decrypted data as well as the ability to permanently damage the operating system.
- Use with caution!
- We strongly discourage the use of keys which are not secured with a passphrase.
- Save
- Your Gibberfish cloud can send daily backups of your data to an offsite server for disaster recovery purposes. This will allow us to restore your data in the event of a failure. Your data is sent to us in an encrypted form which we cannot decipher and we store it securely on an encrypted disk.
- If you wish to enable your server to transmit backups to us you must opt in below. You may opt out again at any time.
- Enabled
- Please enter your encryption passphrase to unlock and launch your Gibberfish cloud.
- Gibberfish is now launching.
- Please do not navigate away from this page until it is complete.
- Launch!
- Gibberfish was installed successfully!
- You may now visit <a href="https://%(nextcloud_domain_name)s" target="_blank">%(nextcloud_domain_name)s</a> and log in using the following temporary credentials.
- Please change your passphrase once you have logged in.
- Starting
- Add New
- The following SSH public keys are installed for the root user:
- Key Fingerprint
- Date Added
- Delete
- None
- Note:
- Changes to SSH keys may take up to 5 minutes to activate
- This will remove the SSH key with the fingerprint
- Are you sure?
- Confirm
- Backup tokens are pre-generated codes which will allow you to authenticate without your phone.
- Each code may only be used once.
- When you have used all of your tokens you will be allowed to generate a new set.
- If you would like to add the following tokens to your account, first copy them down somewhere safe and then click 'Confirm'.
- Please enter your 2nd factor code:
- Verify
- Scan this QR code with your OTP app, then generate a 6-digit code and enter it below.
- Once confirmed you will be required to use your mobile device to log in.
- This will remove your TOTP device configuration and delete all backup tokens.
- Gibberfish Management Portal
- Configure 2FA!
- Get backup tokens
- Reset 2FA
- Logout
- Management Portal
- Deploy
- Backups
- SSH Keys
- Go
- You have been logged out successfully
- Your username and password didn't match. Please try again.
- login
- By clicking 'login' above, you are indicating that you have read and agree to the Terms of Service, which are available <a href='%(tos_url)s'>here</a>
- Please change your Management Portal passphrase.
- Save changes
-
django.po.
Added 61 new segments
and no segments obsoleted.
New segments:
- Enter encryption passphrase
- Username
- Passphrase
- Enter code to confirm
- Old passphrase
- New passphrase
- Confirm new passphrase
- Enter SSH public key
- CAUTION:
- Adding SSH keys will allow 'root' logins on your server.
- The root user will have complete and total access to your decrypted data as well as the ability to permanently damage the operating system.
- Use with caution!
- We strongly discourage the use of keys which are not secured with a passphrase.
- Save
- Your Gibberfish cloud can send daily backups of your data to an offsite server for disaster recovery purposes. This will allow us to restore your data in the event of a failure. Your data is sent to us in an encrypted form which we cannot decipher and we store it securely on an encrypted disk.
- If you wish to enable your server to transmit backups to us you must opt in below. You may opt out again at any time.
- Enabled
- Please enter your encryption passphrase to unlock and launch your Gibberfish cloud.
- Gibberfish is now launching.
- Please do not navigate away from this page until it is complete.
- Launch!
- Gibberfish was installed successfully!
- You may now visit <a href="https://%(nextcloud_domain_name)s" target="_blank">%(nextcloud_domain_name)s</a> and log in using the following temporary credentials.
- Please change your passphrase once you have logged in.
- Starting
- Add New
- The following SSH public keys are installed for the root user:
- Key Fingerprint
- Date Added
- Delete
- None
- Note:
- Changes to SSH keys may take up to 5 minutes to activate
- This will remove the SSH key with the fingerprint
- Are you sure?
- Confirm
- Backup tokens are pre-generated codes which will allow you to authenticate without your phone.
- Each code may only be used once.
- When you have used all of your tokens you will be allowed to generate a new set.
- If you would like to add the following tokens to your account, first copy them down somewhere safe and then click 'Confirm'.
- Please enter your 2nd factor code:
- Verify
- Scan this QR code with your OTP app, then generate a 6-digit code and enter it below.
- Once confirmed you will be required to use your mobile device to log in.
- This will remove your TOTP device configuration and delete all backup tokens.
- Gibberfish Management Portal
- Configure 2FA!
- Get backup tokens
- Reset 2FA
- Logout
- Management Portal
- Deploy
- Backups
- SSH Keys
- Go
- You have been logged out successfully
- Your username and password didn't match. Please try again.
- login
- By clicking 'login' above, you are indicating that you have read and agree to the Terms of Service, which are available <a href='%(tos_url)s'>here</a>
- Please change your Management Portal passphrase.
- Save changes
© 2009-2023 WebTranslateIt Software S.L. Tous droits réservés.
Termes d’utilisation
·
Politique de confidentialité
·
Politique de sécurité